Short answer star trek phase ii enterprise:
Star Trek Phase II was meant to be a TV series that continued the original Star Trek. The Enterprise from the original series was going to be used, but it underwent some changes for the new show including updated interior design and technology. However, Star trek Phase II never aired, leading to its scripts becoming other forms of media such as novels and fan films.
How to Build Your Own Model of Star Trek Phase II Enterprise: A Step-by-Step Guide
If you’re a fan of Star Trek, then building your own model of the Phase II Enterprise is sure to be an exciting and engaging project. This highly detailed ship was featured in early sketches for the original Star Trek series but never made it onto the show; however, with modern technology and creative ingenuity, you can bring this iconic vessel to life right on your tabletop.
Building a model like this takes time and patience, but following these step-by-step instructions will help make the experience thoroughly rewarding!
Step 1: Gather Your Materials
The first thing you need to do when preparing to build your own Phase II model is gather all of the necessary materials. You’ll need:
– A plastic kit of the Phase II Enterprise (you can find these online or at hobby shops)
– A sharp hobby knife
– Sandpaper (various grits from rough to fine)
– Glue (cyanoacrylate works well for attaching small pieces together)
– Paintbrushes in various sizes
– Enamel paint in several colors that match your chosen design – gray, white, black, silver are generally useful ones.
– Clear acrylic gloss coating spray
Once you’ve got everything together, it’s time to get started!
Step 2: Assemble The Basics
Begin by carefully cutting out each part from the plastic kit using a sharp hobby knife. Then use sandpaper or other abrasive tools if needed – carefully smooth any rough edges created during assembly as best possible before continuing ahead since initial surfaces preparation will dictate how successful final look ends up being.
Start fitting larger parts such as fuselage components beginning with halves which form entire structure skins where internal supports go into place squeezed between them. Join two forward sections than attach upper hull fairing over engine nacelle connecting walls allowing for separation compartments at top deck plate edge under bridge dome.
Move onto wings plates followed by ventral strakes underneath thin triangular fillets leading to aft point. Most of the joints are fitting with pairs pushing together mating tabs and slots before glue application.
Step 3: Painting Your Model
When it comes time to paint your model, start by using enamel spray or brushing on a coat of grey paint as an undercoat everywhere that will be visible in final assembly (don’t forget the interior details like bridge windows and shuttlecraft bay openings) allowing it air-dry for at least two hours.
Choose appropriate parts’ colors, starting with primary color mixture such as white-silver-gray-black scheme used typically throughout Star Trek series ships up until USS Discovery which recently introduced more colorful variants. Paint each section gradually overlapping edges carefully blending contours till perfect tone achieved. Don’t rush! This is not about speed but rather precision work so better take your time getting every part looking great. You might want to use two coats depending on the coverage level, waiting awhile between them for drying sake.
Finally, you need clear acrylic gloss coating spray application over most sections giving finishes extra shine making all painted surfaces protected from humidity damage ultimately sealing everything upto
Star Trek Phase II Enterprise FAQ: Everything You Need to Know
Are you a die-hard Star Trek fan? Have you heard about the infamous and ill-fated return of Captain Kirk and crew in Phase II Enterprise, also known as Star Trek: The New Voyages? If not, buckle up because this article is your one-stop-shop for everything you need to know about this never completed series.
Firstly, let’s get some context. In 1977, after the massive success of Star Wars (the movie that changed sci-fi forever), Paramount Studios decided to jump on the bandwagon and re-launch their dormant TV show – Star Trek. Back in those days, original creator Gene Roddenberry still had faith in his vision (which was at critical mass due to the failure of his second project-based Word building called Genesis before release) but the rest of Hollywood seemed less convinced. Either way, work began on what we now know as Phase II Enterprise.
The story followed the beloved characters from The Original Series who were now older but still ready for adventure aboard a new starship called USS Enterprise NCC-1701 refit which (in our timeline) first appeared with them fighting Kahn Noonien Singh leading to Spock’s death so that he can be resurrected internally thanks again to Genesis by Kirk going rogue breaching protocol… Whoops too much information!
Anyway back to phase II enterprise FAQs:
Q: What Changes Were Made To The Ship From The Old Show?
A: A lot actually! Due to advances in technology since TOS era filming quality increased allowing for better special effects such as warp speed wind shielding when using artificial gravity rather than cel-gel packs floating during scene cuts! Another notable change is that all doors slide open automatically hands free battery powered panels instead of conventional hinges or push plates needing manual operation by hand switches like old school ‘classic’ Doors.
Q: Who Was Cast For This New Adventure?
A: Many familiar faces returned including William Shatner as Captain James T. Kirk, Leonard Nimoy as Mr. Spock, DeForest Kelley as Dr. McCoy, and Nichelle Nichols returning to her role of Lt Uhura despite rumor mills saying she was ‘too old’! There were also some new faces including the female Vulcan named Xon who (fun fact!) was supposed to replace Spock when he left the show after season five that never happened). Adrienne Barbeau from Birds Of Prey television series appeared on board Enterprise too!
Q: Did Any Episodes Get Filmed?
A: Yes, there are three episodes that were completed before production halted above all thanks to longer than anticipated visual effects finalizing time leading towards increased project costs by ViacomCBS investors losing faith in projected ROI or Return On Investment especially given their low success rated ventures like Gene Roddenberry’s previous project Genesis coupled with multiple cancelled back then now-classic shows such as Star Wars Clone Wars animated series which may have negatively influenced Paramount executives personally.
So there you have it – a brief(ish) overview of Phase II Enterprise aka The
Behind the Scenes of Star Trek Phase II Enterprise: The Making and Legacy
Star Trek Phase II Enterprise is one of the most iconic spaceships in science fiction history and remains hugely popular among fans. While it only appeared for a brief period during the mid-1970s, its legacy has remained strong until today.
But what really went into the making of this beloved spaceship? The behind-the-scenes story is both fascinating and extensive, with many interesting details about how this impressive vessel came to be.
Firstly, it’s important to understand that Star Trek Phase II was originally intended to serve as a follow-up series to the original Star Trek show. However, due to various issues including budget constraints and conflicts between cast members, it never got off the ground – despite plans already being made for new sets and stars.
One of these planned stories would have seen Admiral Kirk becoming captain once again on board an upgraded USS Enterprise. This led directly to work on designing a brand-new ship; one which would represent all the latest advancements in space travel.
The exciting challenge fell upon legendary designer Matt Jefferies (who also coordinated much of Enterprise’s creation) who took inspiration from real NASA designs but added his signature sci-fi twist, resulting ultimately in a sleeker more streamlined design than her predecessor with enhanced weapons systems and technical capabilities — while still incorporating classic elements such as saucer section engineering principles pioneered by Gene Roddenberry himself.
Jefferies’ bravery didn’t stop there though! As he knew his modernized vision must pay homage whilst satisfying diehard Trekkie fans… And thus began using feature character point-of-view shots or “romantic” widescreen camera angles primarily showing off actor William Shatner sitting atop glorious refurbished console panels designed straight outta’ 1966!
Finally after months of endless brainstorming we see gleaming metallic plates begin assembly as vocal team Elmer Bernstein adds their own contributions onto remarkable visuals by TV director Robert Wise – cemented by experimental composer Jerry Goldsmith’s immortal score.
The demise of the Star Trek Phase II television show allowed the designers free reign to continue designing beyond where they had been and include their expanded ideas for features not previously possible while working in a frantic time-frame environment.
As a result, the Enterprise ended up being one of the most intricate ships ever created for science fiction- even though her appearance was brief. Her influence continued long after she left screens; inspiring generations of sci-fi fans who’ve remained dedicated to learning about every aspect behind this landmark “version” vessel that almost brought Star Trek back onto TV… And has influenced designers ever since!
